First draft of updates to manual to include the installation instructions for the new ipod bootloader. Still needs a lot of clean-up. Also flipped the installation instructions for the bootloader and the firmware build for all SWCODEC platforms. Instructions for installing the build now come before instructions for installing the bootloader. This should eliminate some confusion from those who tried to boot Rockbox after installing the bootloader but before installing a build, and received the -1 error.

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11829 a1c6a512-1295-4272-9138-f99709370657

2 files changed, 177 insertions, 390 deletions

diff --git a/manual/getting_started/installation.tex b/manual/getting_started/installation.tex
index 4accc0658d..7d6b678a4e 100644
--- a/manual/getting_started/installation.tex
+++ b/manual/getting_started/installation.tex
@@ -111,14 +111,7 @@ software.
 
   \end{description}
 
-  \subsection{Installing the boot loader}
-  \opt{h1xx,h300}{\input{getting_started/iriver_install.tex}}
-  \opt{ipod}{\input{getting_started/ipod_install.tex}}
-  \opt{x5}{\input{getting_started/iaudio_install.tex}}
-  \opt{h10,h10_5gb}{\input{getting_started/h10_install.tex}}
-
   \subsection{Installing the firmware}
-  After installing the boot loader, the installation becomes fairly easy.
 }
 
 There are three different types of firmware binaries from Rockbox website:
@@ -192,6 +185,14 @@ directory structure that Rockbox needs.
   number of other folders and system files needed by Rockbox. If you receive a
   ``-1'' error when you start Rockbox, you have not extracted the contents of
   the \fname{.zip} file to the proper location.
+        }
+
+\opt{SWCODEC}{
+  \subsection{Installing the boot loader}
+  \opt{h1xx,h300}{\input{getting_started/iriver_install.tex}}
+  \opt{ipod}{\input{getting_started/ipod_install.tex}}
+  \opt{x5}{\input{getting_started/iaudio_install.tex}}
+  \opt{h10,h10_5gb}{\input{getting_started/h10_install.tex}}
 }
 
 \section{Enabling Speech Support (optional)}\label{sec:enabling_speech_support}
diff --git a/manual/getting_started/ipod_install.tex b/manual/getting_started/ipod_install.tex
index 08ed229c43..6c36edead3 100755
--- a/manual/getting_started/ipod_install.tex
+++ b/manual/getting_started/ipod_install.tex
@@ -1,391 +1,177 @@
 % $Id$ %
 
-\warn{A significantly easier installation method has been 
-developed for the ipods, but is not yet included in this manual.  Until this 
-manual is updated, please visit 
-\url{http://www.rockbox.org/twiki/bin/view/Main/IpodInstallationBeta} 
-for the most up-to-date version of the installation instructions.}
-
-\opt{ipodvideo}{\warn{In addition, the instructions in this manual do not work 
-at all on the new ``5.5g'' video ipod.  If you own such an ipod - you 
-\emph{must} use the new instructions at
-\url{http://www.rockbox.org/twiki/bin/view/Main/IpodInstallationBeta}}}
-
 \opt{ipodnano}{\warn{If your Nano has a stainless steel back and plastic front 
 it is a 1st generation and is compatible with Rockbox.  If, on the other hand, 
 your Nano has a one-piece aluminum body it is a 2nd generation Nano and there 
 is currently no Rockbox port available.  Do not attempt to install the 
 bootloader on a 2nd generation Nano}}
 
-  Installing the boot loader is the trickiest part of the installation.
-  \opt{ipodnano}{First, you need to find out which version of the Apple
-    firmware you're running. To do this, start the Apple firmware and go to
-    Settings screen. In the ``About'' screen you'll find the version number
-    of the Apple firmware. Depending on the version number the installation
-    is slightly different.}%
-    
-  The process is different depending on your operating system, but before
-  starting, connect the \dap{} to the computer using either an USB
-  %\fixme{or Firewire?} % Firewire is currently not supported.
-  cable. Next, create a folder on the computer's hard drive and
-  download the following file to that folder:
-  \opt{ipodvideo}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-video.bin}}
-  \opt{ipodnano}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-nano.bin}}
-  \opt{ipodmini}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-mini1g.bin} or
-    \url{http://download.rockbox.org/bootloader/ipod/bootloader-mini2g.bin} depending on which
-    generation your \dap{} is.\fixme{Describe how to identify 1/2G}}
-  \opt{ipodcolor}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-color.bin}}
-  \opt{ipod4g}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-4g.bin}}
-  \opt{ipod3g}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-3g.bin}}
-
-  When that is done, proceed to the section below that matches the operating
-  system on the computer.
-  \note{These instructions all require you to have administrator rights
-  on your computer, regardless of the operating system.}
-  \note{Rockbox only works on FAT32 partitions (called ``Windows formatted'' by
-    Apple). So if your \dap{} is Mac formatted (HFS+), you should first convert
-    it to FAT32. Information on how to do this can be found on the Rockbox
-    website. \fixme{Include these instructions?}}
-
-\subsubsection{Windows users}
-\begin{enumerate}
-  \item Download the following two programs and save them in the folder just
-    created. These programs will be used in the next steps:
-    \begin{itemize}
-      \item \url{http://download.rockbox.org/bootloader/ipod/ipodpatcher.exe}
-      \item \url{http://download.rockbox.org/bootloader/ipod/ipod_fw.exe}
-    \end{itemize}
-  \item Locate the \dap{} by opening a command window. You can do this by
-    clicking ``Start'', ``Run'' and typing \fname{cmd}. Press Enter to
-    execute that command. Now change directory to the
-    folder you created and run the following commands:
-    \begin{code}
-    ipodpatcher 0
-    ipodpatcher 1
-    ipodpatcher 2
-    ipodpatcher 3
-    \end{code}
-    Keep increasing the number until the \dap{} is located.
-
-    The output for an unsuccessful attempt to contact the \dap{} looks like
-    this:
-    \begin{code}
-    C:\textbackslash{}rockbox>ipodpatcher 0
-    ipodpatcher v0.3 - (C) Dave Chapman 2006
-    This is free software; see the source for copying conditions.  There is NO
-    warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
-
-    [INFO] Reading partition table from \textbackslash\textbackslash{}.\textbackslash{}PhysicalDrive0
-    Drive is not an iPod, aborting
-    \end{code}
-    
-    A successful connection to the \dap{} will look similar to this...
-    \begin{code}
-    C:\textbackslash{}rockbox>ipodpatcher 6
-    ipodpatcher v0.3 - (C) Dave Chapman 2006
-    This is free software; see the source for copying conditions.  There is NO
-    warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
-
-    [INFO] Reading partition table from \textbackslash\textbackslash{}.\textbackslash{}PhysicalDrive6
-    Part    Start Sector    End Sector    Size (MB)  Type
-       0              63        160649        78.4   Empty (0x00)
-       1          160650       7984304      3820.1   W95 FAT32 (0x0b)
-   \end{code}
-    Remember the number that corresponds to your \dap{} -- in the 
-    following steps, \emph{N} should be replaced with the number just found.
-  \item Now, extract the firmware partition currently on the \dap{} with the
-    following command:
-    \begin{code}
-    ipodpatcher -r \emph{N} bootpartition.bin
-    \end{code}
-    \note{You should keep a safe backup of this \fname{bootpartition.bin} file
-      for use if you ever wish to either upgrade the Rockbox boot loader or
-      uninstall Rockbox from your Ipod}
-  \item Extract the Apple firmware from the partition image image just created:
-    \begin{code}
-    ipod_fw -o apple_os.bin -e 0 bootpartition.bin
-    \end{code}
-  \opt{ipodnano}{\note{The following step is only necessary if your Apple
-    firmware has version 1.2 or later. If this doesn't apply to you, simply 
-    skip it.}}
-\optv{ipodvideo,ipodnano}{
-  \item
-    Similarly, extract the Broadcom firmware:
-    \begin{code}
-    ipod_fw -o apple_sw_5g_rcsc.bin -e 1 bootpartition.bin
-    \end{code}
-}
-  \item Merge the Rockbox boot loader you downloaded previously with the Apple
-    firm\-ware.%
-\optv{ipodnano}{
-    If your firmware version is lower than 1.2 this works you need
-    this command:
-    \begin{code}
-    ipod_fw -g nano -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-    If your firmware version is 1.2 or later you need to use the following 
-    command instead. Please note that the ``video'' is correct.
-    \begin{code}
-    ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-}
-\optv{ipodvideo}{
-    \begin{code}
-    ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-video.bin
-    \end{code}
-}
-\optv{ipodmini}{
-    \begin{code}
-    ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini1g.bin
-    \end{code}
-    Or, if you have a 2G mini:
-    \begin{code}
-    ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini2g.bin
-    \end{code}
-}
-\optv{ipodcolor}{
-    \begin{code}
-    ipod_fw -g color -o rockboot.bin -i apple_os.bin bootloader-color.bin
-    \end{code}
-}
-\optv{ipod4g}{
-    \begin{code}
-    ipod_fw -g 4g -o rockboot.bin -i apple_os.bin bootloader-4g.bin
-    \end{code}
-}
-\optv{ipod3g}{
-    \begin{code}
-    ipod_fw -g 3g -o rockboot.bin -i apple_os.bin bootloader-3g.bin
-    \end{code}
-}
-\item
-    Install the Rockbox-enabled firmware:
-    \begin{code}
-    ipodpatcher -w \emph{N} rockboot.bin
-    \end{code}
-\end{enumerate}
-
-Now you can proceed installing the firmware itself.
-
-\subsubsection{Mac OS X users}
-\begin{enumerate}
-  \item Download the following two programs and save them in the folder just
-    created. These programs will be used in the next steps:
-    \begin{itemize}
-      \item \url{http://download.rockbox.org/bootloader/ipod/diskdump}
-      \item \url{http://download.rockbox.org/bootloader/ipod/ipod_fw}
-    \end{itemize}
-    Start a Terminal and type navigate into the folder you created. Before
-    you can continue, you need to ensure that Mac OS knows that the
-    \fname{ipod\_fw}
-    and diskdump files you downloaded are executable programs. To do this,
-    type the following command:
-    \begin{code}
-    chmod +x ipod_fw diskdump
-    \end{code}
-  \item Locate the \dap{} by running the following command:
-    \begin{code}
-    mount
-    \end{code}
-    The output will look something like this: \fixme{Add full example}
-    \begin{code}
-    /dev/disk1s2 on /Volumes/DAVE_S IPOD 1 (local, nodev, nosuid)
-    \end{code}
-    In this example, the \dap\ is located at /dev/disk1s2 Remember the 
-    location of your \dap\  -- in the following steps, /dev/disk1s2 should be
-    replaced with the location just found.
-  \item Before continuing, the \dap\ must be ``unmounted'', which is
-    done with the following command:
-    \begin{code}
-    diskutil unmount /dev/disk1s2
-    \end{code}
-  \item Now, extract the Apple firmware currently on the \dap{} with the
-    following command:
-    \note{The last part of the location is left out.}
-    \begin{code}
-    ./diskdump -r /dev/disk1 bootpartition.bin
-    \end{code}
-    \note{You should keep a safe backup of this \fname{bootpartition.bin} file
-      for use if you ever wish to either upgrade the Rockbox bootloader or
-      uninstall Rockbox from your iPod
-    }
-  \item Extract the Apple firmware from this partition image:
-    \begin{code}
-    ./ipod_fw -o apple_os.bin -e 0 bootpartition.bin
-    \end{code}
-  \opt{ipodnano}{\note{The following step is only necessary if your Apple
-    firmware has version 1.2 or later. If this doesn't apply to you, simply 
-    skip it.}}
-\optv{ipodvideo,ipodnano}{
-  \item
-    Similarly, extract the Broadcom firmware:
-    \begin{code}
-    ./ipod_fw -o apple_sw_5g_rcsc.bin -e 1 bootpartition.bin
-    \end{code}
-}
-  \item Merge the Rockbox bootloader you downloaded previously with the Apple
-    firm\-ware.%
-\optv{ipodnano}{
-    If your firmware version is lower than 1.2 this works you need
-    this command:
-    \begin{code}
-    ./ipod_fw -g nano -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-    If your firmware version is 1.2 or later you need to use the following 
-    command instead. Please note that the ``video'' is correct.
-    \begin{code}
-    ./ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-}
-\optv{ipodvideo}{
-    \begin{code}
-    ./ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-video.bin
-    \end{code}
-}
-\optv{ipodmini}{
-    \begin{code}
-    ./ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini1g.bin
-    \end{code}
-    Or, if you have a 2G Mini:
-    \begin{code}
-    ./ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini2g.bin
-    \end{code}
-}
-\optv{ipodcolor}{
-    \begin{code}
-    ./ipod_fw -g color -o rockboot.bin -i apple_os.bin bootloader-color.bin
-    \end{code}
-}
-\optv{ipod4g}{
-    \begin{code}
-    ./ipod_fw -g 4g -o rockboot.bin -i apple_os.bin bootloader-4g.bin
-    \end{code}
-}
-\optv{ipod3g}{
-    \begin{code}
-    ./ipod_fw -g 3g -o rockboot.bin -i apple_os.bin bootloader-3g.bin
-    \end{code}
-}
-  \item
-    Install the Rockbox-enabled firmware:
-    \note{The last part of the location is left out.}
-    \begin{code}
-    ./diskdump -w /dev/disk1 rockboot.bin
-    \end{code}
-\end{enumerate}
-
-Now, proceed with installing the firmware itself.
-
-\subsubsection{Linux users}
-\begin{enumerate}
-  \item Download the following and save it in the folder just
-    created:
-    \begin{itemize}
-      \item \url{http://www.rockbox.org/viewcvs.cgi/*checkout*/tools/ipod_fw.c}
-    \end{itemize}
-    Now compile it to an executable by opening a command prompt and changing
-    to the folder created previously. Then run the following command:
-    \begin{code}
-    gcc -o ipod_fw ipod_fw.c
-    \end{code}
-    If you get the message that the command gcc is not found, you need to
-    install gcc. How to do this depends on your Linux distribution, and
-    you should consult its documentation for help on this.
-  \item Locate your Ipod by running the command \verb|dmesg|. In the output
-    something like the following should be seen:
-\begin{code}
-    usb 4-1: new high speed USB device using ehci_hcd and address 7
-    scsi4 : SCSI emulation for USB Mass Storage devices
-    usb-storage: device found at 7
-    usb-storage: waiting for device to settle before scanning
-      Vendor: Apple     Model: iPod              Rev: 1.62
-      Type:   Direct-Access                      ANSI SCSI revision: 00
-    SCSI device sdb: 58605120 512-byte hdwr sectors (30006 MB)
-\end{code}
-    You need the device name of your \dap, which you can find in the last line.
-    In this example, the \dap\ is located on \fname{/dev/sdb}. In the following,
-    \fname{/dev/sdb} should be replaced with the location just found.
-  \item Run \verb|fdisk -l /dev/sdb|. Verify that the
-    output is similar to the one below:
-    \begin{code}
-       Device Boot      Start         End      Blocks   Id  System
-    /dev/sdb1               1          10       80293+   0  Empty
-    /dev/sdb2              11        3648    29222235    b  W95 FAT32
-    \end{code}
-  \item Back up the partition table using the following command:
-    \note{The last part of the location is left out.}
-    \begin{code}
-    dd if=/dev/\emph{sdb} of=mbr.bin count=1
-    \end{code}
-
-  \item Now, extract the firmware partition currently on the \dap{} with the
-    following command:
-    \begin{code}
-    dd if=/dev/\emph{sdb1} of=bootpartition.bin
-    \end{code}
-    \note{You should keep a safe backup of this \fname{bootpartition.bin} file
-      for use if you ever wish to either upgrade the Rockbox bootloader or
-      uninstall Rockbox from your Ipod
-    }
-  \item Extract the Apple firmware from this partition image:
-    \begin{code}
-    ./ipod_fw -o apple_os.bin -e 0 bootpartition.bin
-    \end{code}
-  \opt{ipodnano}{\note{The following step is only necessary if your Apple
-    firmware has version 1.2 or later. If this doesn't apply to you, simply 
-    skip it.}}
-\optv{ipodvideo,ipodnano}{
-  \item
-    Similarly, extract the Broadcom firmware:
-    \begin{code}
-    ./ipod_fw -o apple_sw_5g_rcsc.bin -e 1 bootpartition.bin
-    \end{code}
-}
-
-  \item Merge the Rockbox bootloader you downloaded previously with the Apple
-    firm\-ware.%
-\optv{ipodnano}{
-    If your firmware version is lower than 1.2 this works you need
-    this command:
-    \begin{code}
-    ./ipod_fw -g nano -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-    If your firmware version is 1.2 or later you need to use the following 
-    command instead. Please note that the ``video'' is correct.
-    \begin{code}
-    ./ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-nano.bin
-    \end{code}
-
-}
-\optv{ipodvideo}{
-    \begin{code}
-    ./ipod_fw -g video -o rockboot.bin -i apple_os.bin bootloader-video.bin
-    \end{code}
-}
-\optv{ipodmini}{
-    \begin{code}
-    ./ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini1g.bin
-    \end{code}
-    Or, if you have a 2G Mini:
-    \begin{code}
-    ./ipod_fw -g mini -o rockboot.bin -i apple_os.bin bootloader-mini2g.bin
-    \end{code}
-}
-\optv{ipodcolor}{
-    \begin{code}
-    ./ipod_fw -g color -o rockboot.bin -i apple_os.bin bootloader-color.bin
-    \end{code}
-}
-\optv{ipod4g}{
-    \begin{code}
-    ./ipod_fw -g 4g -o rockboot.bin -i apple_os.bin bootloader-4g.bin
-    \end{code}
-}
-  \item
-    Install the Rockbox-enabled firmware:
-    \begin{code}
-    dd if=rockboot.bin of=/dev/\emph{sdb1}
-    \end{code}
-\end{enumerate}
-Now you can install the firmware itself.
-
+In order to make your iPod load and execute the Rockbox firmware you have just 
+installed, you will need to install the Rockbox bootloader. Unless bugs are 
+found in the bootloader code, or significant new feature are added, you will 
+only have to perform this step once.
+
+The following instructions refer to the ``installation folder.''  For Windows 
+users, the "installation folder" is assumed to be a folder in the root (top-
+level) of the C: drive called \fname{rockbox} (you will obviously need to 
+create this folder yourself).  For Mac OS X and Linux users, the ``installation 
+folder'' is assumed to be the Desktop folder. But you can use any folder 
+you wish. Note that these files should be saved onto your computer's hard disk, 
+\emph{not} on your Ipod. 
+
+\begin{enumerate} 
+
+  \item First, download the \fname{ipodpatcher} tool to your installation 
+  folder.  You can download the \fname{ipodpatcher} tool for your operating 
+  system at 
+  \url{http://www.rockbox.org/twiki/bin/view/Main/IpodInstallationBeta}.
+  
+  \item Next, download the following file to the installation folder: 
+
+    \opt{ipodvideo}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    video.ipod}} 
+    \opt{ipodnano}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    nano.ipod}} 
+    \opt{ipodmini}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    mini1g.ipod} or \url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    mini2g.ipod} depending on which generation your \dap{} is.  \fixme{Describe 
+    how to identify 1/2G}} 
+    \opt{ipodcolor}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    color.ipod}} 
+    \opt{ipod4g}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    4g.ipod}} 
+    \opt{ipod3g}{\url{http://download.rockbox.org/bootloader/ipod/bootloader-
+    3g.ipod}}
+
+  \item Next, open a command prompt (Windows) or terminal window (Mac OSX and Linux).
+  
+    Windows users will perform this and the following steps from the Windows 
+    command prompt. Start a command prompt and navigate to the isntallation 
+    directory.
+
+    Mac OS X and Linux/Unix users will perform these steps from the Terminal. 
+    Start a new terminal window and navigate to the Desktop folder (type cd 
+    Desktop into the terminal and press enter). You then need to ensure that the 
+    ipodpatcher program is ``executable'' by typing the command chmod +x 
+    ipodpatcher and then pressing enter.
+  
+  \item Connect your ipod to your computer.
+
+                If you haven't already done so, you should now plug your iPod into your 
+                computer (via either the USB or Firewire cable).
+
+                \fixme{Notes about closing itunes, enabling the ``show ipod as disk'' option 
+                in ipod, anything else?}
+
+        \item Find your ipod with ipodpatcher (Windows users only)
+
+                Windows users:  Type the following command to search for ipods attached to 
+                your computer: 
+                        \begin{code} 
+                                ipodpatcher \-\-scan 
+                        \end{code}
+                
+                When ipodpatcher finds your ipod, remember the number it displays - this 
+                will    be the number you use to access your ipod in the following steps.
+
+                \note{Windows users require administrator rights for running    ipodpatcher. 
+                Either re-login as administrator, or open a command prompt running under an 
+                administrator account by using one of the "Run as" features     of Windows XP.}
+
+        \item Find your ipod (Mac OS X users only)
+
+                Attach your iPod to your Mac (using either USB or Firewire) and wait for 
+                iTunes to open. When iTunes opens, close it down.  In your Terminal window, 
+                type the command mount and press enter. This will list all the disks (and 
+                other devices) that are "mounted" on your computer. The last    drive in the 
+                list should be your iPod. For example: 
+                \begin{code}
+                         /dev/disk1s2 on /Volumes/DAVE_S IPOD 1 (local, nodev, nosuid) 
+                \end{code}
+
+                In order to install the ipod bootloader, you need to "unmount" this disk 
+                using   the following command: 
+                        \begin{code} 
+                                diskutil unmount /dev/disk1s2 
+                        \end{code}
+                        
+                replacing ``/dev/disk1s2'' with the device name Mac OS has assigned to your
+                ipod. This may take a few seconds, after which Mac OS will say ``Volume 
+                /dev/disk1s2 unmounted.''       ``/dev/disk1s2'' refers to the second partition on 
+                /dev/disk1 - remember   ``/dev/disk1'' for the next step.
+
+                It's possible that itunes will try to be ``helpful'' and remount your ipod 
+                after you modify it with ipodpatcher. If this happens, you need to unmount 
+                it again using the above command. 
+  
+        \item Create a backup of your ipod's firmware partition
+
+                Type the following command, replacing "[device]" with the number (for 
+                Windows users) or the device name (Mac OS X and Unix users) assigned to 
+                your ipod that  you found in the previous step: 
+                        \begin{code} 
+                                ipodpatcher [device] -r bootpartition.bin (Windows) 
+                        \end{code}
+
+                        or
+
+                        \begin{code}
+                                ./ipodpatcher [device] -r bootpartition.bin (Mac OS X/Unix)
+                        \end{code}
+        
+                This should create a file in the current folder called bootpartition.bin 
+                (approximately 40MB for the iPod 3G, 4G and Color/Photo, 80MB for the Nano 
+                1st gen and 30GB Video, and 112MB for the 60GB Video) containing a copy of 
+                the ``firmware partition'' from your iPod.
+
+                If it ever becomes necessary (i.e. your ipod refuses to start), you can 
+                restore this backup to your ipod using the command ipodpatcher [device] -w 
+                bootpartition.bin (Windows) or ./ipodpatcher [device] -w bootpartition.bin 
+                (Mac OS X/Unix).   
+        
+        \item Install the bootloader.
+
+                Windows users should now type:
+                \begin{code}
+                        ipodpatcher [device] -a 
+                                \opt{ipodvideo}{bootloader-video.ipod}
+                \opt{ipodnano}{bootloader-nano.ipod}
+                          \opt{ipodmini}{bootloader-mini1g.ipod 
+                                \end{code} 
+                                or
+                                \begin{code}
+                                        ipodpatcher [device] -a bootloader-mini2g.ipod
+                                }
+                \opt{ipodcolor}{bootloader-color.ipod}
+                    \opt{ipod4g}{bootloader-4g.ipod}
+                    \opt{ipod3g}{bootloader-3g.ipod}
+                \end{code}
+
+                and Mac OS X/Unix users should type:
+                \begin{code}
+                        ./ipodpatcher [device] -a 
+                        \opt{ipodvideo}{bootloader-video.ipod}
+                \opt{ipodnano}{bootloader-nano.ipod} 
+                          \opt{ipodmini}{bootloader-mini1g.ipod 
+                                \end{code} 
+                                or
+                                \begin{code}
+                                        or ipodpatcher [device] -a bootloader-mini2g.ipod
+                                }
+                \opt{ipodcolor}{bootloader-color.ipod}
+                    \opt{ipod4g}{bootloader-4g.ipod}
+                    \opt{ipod3g}{bootloader-3g.ipod}
+                \end{code}
+
+        Replace [device] with the number (Windows users) or device name (Mac OS X/Unix 
+        users) you've been using to access your ipod.
+
+        You can now disconnect your ipod from your computer in the normal way. This 
+        should cause your iPod to reboot and start Rockbox.
+
+        \item Troubleshooting.
+
+        \fixme{Add some notes here about common problems - "rockbox error -1" is the 
+        main one. Or maybe have a new troubleshooting page.}
+  
+\end{enumerate} 
\ No newline at end of file