AXP PMU rewrite (again)

I noticed a few mistakes in the old driver code and it was in
need of an overhaul anyway... I decided to scale things back,
simplify the code and remove most of the debug menus, netting
a nice code size savings.

One new feature is an advanced debug menu which is accessible
by recompiling the code with AXP_EXTRA_DEBUG. It adds quite a
bit of code size and isn't useful other than for development
so it must be manually enabled by editing the source.

Change-Id: I30e17c1194c14823decd726a574ed14451d4cb2d

1 files changed, 30 insertions, 19 deletions

diff --git a/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c b/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
index 75f8031dd9..65d1bc163f 100644
--- a/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
+++ b/firmware/target/mips/ingenic_x1000/shanlingq1/power-shanlingq1.c
@@ -22,7 +22,7 @@
 #include "power.h"
 #include "adc.h"
 #include "system.h"
-#include "axp-pmu.h"
+#include "axp192.h"
 #ifdef HAVE_CW2015
 # include "cw2015.h"
 #endif
@@ -73,24 +73,30 @@ const unsigned short percent_to_volt_charge[11] =
 void power_init(void)
 {
     i2c_x1000_set_freq(AXP_PMU_BUS, I2C_FREQ_400K);
-    axp_init();
 #ifdef HAVE_CW2015
     cw2015_init();
 #endif
 
-    /* Change supply voltage from the default of 1250 mV to 1200 mV,
-     * this matches the original firmware's settings. Didn't observe
-     * any obviously bad behavior at 1250 mV, but better to be safe. */
-    axp_supply_set_voltage(AXP_SUPPLY_DCDC2, 1200);
-
-    /* For now, just turn everything on... definitely the touchscreen
-     * is powered by one of the outputs */
-    i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
-                    AXP_REG_PWROUTPUTCTRL1, 0, 0x05, NULL);
-    i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
-                    AXP_REG_PWROUTPUTCTRL2, 0, 0x0f, NULL);
-    i2c_reg_modify1(AXP_PMU_BUS, AXP_PMU_ADDR,
-                    AXP_REG_DCDCWORKINGMODE, 0, 0xc0, NULL);
+    /* Set DCDC2 to 1.2 V to match OF settings. */
+    axp_set_supply_voltage(AXP_SUPPLY_DCDC2, 1200);
+
+    /* Power on required supplies */
+    axp_set_enabled_supplies(
+        (1 << AXP_SUPPLY_DCDC1) | /* SD bus (3.3 V) */
+        (1 << AXP_SUPPLY_DCDC2) | /* LCD (1.2 V) */
+        (1 << AXP_SUPPLY_DCDC3) | /* CPU (1.8 V) */
+        (1 << AXP_SUPPLY_LDO2) |  /* Touchscreen (3.3 V) */
+        (1 << AXP_SUPPLY_LDO3));  /* not sure (2.5 V) */
+
+    /* Enable required ADCs */
+    axp_set_enabled_adcs(
+        (1 << AXP_ADC_BATTERY_VOLTAGE) |
+        (1 << AXP_ADC_CHARGE_CURRENT) |
+        (1 << AXP_ADC_DISCHARGE_CURRENT) |
+        (1 << AXP_ADC_VBUS_VOLTAGE) |
+        (1 << AXP_ADC_VBUS_CURRENT) |
+        (1 << AXP_ADC_INTERNAL_TEMP) |
+        (1 << AXP_ADC_APS_VOLTAGE));
 
     /* Delay to give power output time to stabilize */
     mdelay(20);
@@ -111,23 +117,28 @@ void power_off(void)
 
 bool charging_state(void)
 {
-    return axp_battery_status() == AXP_BATT_CHARGING;
+    return axp_is_charging();
+}
+
+unsigned int power_input_status(void)
+{
+    return axp_power_input_status();
 }
 
 int _battery_voltage(void)
 {
     /* CW2015 can also read battery voltage, but the AXP consistently
      * reads ~20-30 mV higher so I suspect it's the "real" voltage. */
-    return axp_adc_read(ADC_BATTERY_VOLTAGE);
+    return axp_read_adc(AXP_ADC_BATTERY_VOLTAGE);
 }
 
 #if CONFIG_BATTERY_MEASURE & CURRENT_MEASURE
 int _battery_current(void)
 {
     if(charging_state())
-        return axp_adc_read(ADC_CHARGE_CURRENT);
+        return axp_read_adc(AXP_ADC_CHARGE_CURRENT);
     else
-        return axp_adc_read(ADC_DISCHARGE_CURRENT);
+        return axp_read_adc(AXP_ADC_DISCHARGE_CURRENT);
 }
 #endif