diff options
author | Torne Wuff <torne@wolfpuppy.org.uk> | 2010-01-31 11:07:29 +0000 |
---|---|---|
committer | Torne Wuff <torne@wolfpuppy.org.uk> | 2010-01-31 11:07:29 +0000 |
commit | 533cf7737bae4363edefbfb202cb44e9eb30cd3f (patch) | |
tree | abfb69b76b46fc8d22c14023969ba3fcaad4809d /firmware/target/arm/ata-pp5020.c | |
parent | c0e2d9fe1bb87730d9a8a7cac3cb8f6cd39ce630 (diff) | |
download | rockbox-533cf7737bae4363edefbfb202cb44e9eb30cd3f.tar.gz rockbox-533cf7737bae4363edefbfb202cb44e9eb30cd3f.zip |
Enable ATA DMA on pp5020 based players with ATA drives.
DMA is only used for reading because writing seems to be slower with DMA.
Only requests which are cacheline aligned (16 bytes) will use DMA, so many
requests will still use PIO at this point; a later change will align more
reads.
Part of FS#9708, original DMA code by Boris Gjenero (dreamlayers).
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24405 a1c6a512-1295-4272-9138-f99709370657
Diffstat (limited to 'firmware/target/arm/ata-pp5020.c')
-rw-r--r-- | firmware/target/arm/ata-pp5020.c | 183 |
1 files changed, 183 insertions, 0 deletions
diff --git a/firmware/target/arm/ata-pp5020.c b/firmware/target/arm/ata-pp5020.c index 8e2200c901..c8ce148dd7 100644 --- a/firmware/target/arm/ata-pp5020.c +++ b/firmware/target/arm/ata-pp5020.c | |||
@@ -48,6 +48,12 @@ void ata_device_init() | |||
48 | #ifdef SAMSUNG_YH920 | 48 | #ifdef SAMSUNG_YH920 |
49 | CPU_INT_DIS = (1<<IDE_IRQ); | 49 | CPU_INT_DIS = (1<<IDE_IRQ); |
50 | #endif | 50 | #endif |
51 | #ifdef HAVE_ATA_DMA | ||
52 | IDE_DMA_CONTROL |= 2; | ||
53 | IDE_DMA_CONTROL &= ~1; | ||
54 | IDE0_CFG &= ~0x8010; | ||
55 | IDE0_CFG |= 0x20; | ||
56 | #else | ||
51 | 57 | ||
52 | /* From ipod-ide.c:ipod_ide_register() */ | 58 | /* From ipod-ide.c:ipod_ide_register() */ |
53 | IDE0_CFG |= (1<<5); | 59 | IDE0_CFG |= (1<<5); |
@@ -56,7 +62,184 @@ void ata_device_init() | |||
56 | #else | 62 | #else |
57 | IDE0_CFG &=~(0x10000000); /* cpu < 65MHz */ | 63 | IDE0_CFG &=~(0x10000000); /* cpu < 65MHz */ |
58 | #endif | 64 | #endif |
65 | #endif | ||
59 | 66 | ||
60 | IDE0_PRI_TIMING0 = 0x10; | 67 | IDE0_PRI_TIMING0 = 0x10; |
61 | IDE0_PRI_TIMING1 = 0x80002150; | 68 | IDE0_PRI_TIMING1 = 0x80002150; |
62 | } | 69 | } |
70 | |||
71 | /* These are PIO timings for 80 Mhz. At 24 Mhz, | ||
72 | the first value is 0 but the rest are the same. | ||
73 | They go in IDE0_PRI_TIMING0. | ||
74 | |||
75 | Rockbox used 0x10, and test_disk shows that leads to faster PIO. | ||
76 | If 0x10 is incorrect, these timings may be needed with some devices. | ||
77 | static const unsigned long pio80mhz[] = { | ||
78 | 0xC293, 0x43A2, 0x11A1, 0x7232, 0x3131 | ||
79 | }; | ||
80 | */ | ||
81 | |||
82 | #ifdef HAVE_ATA_DMA | ||
83 | /* Timings for multi-word and ultra DMA modes. | ||
84 | These go in IDE0_PRI_TIMING1 | ||
85 | */ | ||
86 | static const unsigned long tm_mwdma[] = { | ||
87 | 0xF9F92, 0x56562, 0x45451 | ||
88 | }; | ||
89 | |||
90 | static const unsigned long tm_udma[] = { | ||
91 | 0x800037C1, 0x80003491, 0x80003371, | ||
92 | #if ATA_MAX_UDMA > 2 | ||
93 | 0x80003271, 0x80003071 | ||
94 | #endif | ||
95 | }; | ||
96 | |||
97 | #if ATA_MAX_UDMA > 2 | ||
98 | static bool dma_boosted = false; | ||
99 | static bool dma_needs_boost; | ||
100 | #endif | ||
101 | |||
102 | /* This function sets up registers for 80 Mhz. | ||
103 | Ultra DMA mode 2 works at 30 Mhz. | ||
104 | */ | ||
105 | void ata_dma_set_mode(unsigned char mode) { | ||
106 | int modeidx; | ||
107 | |||
108 | (*(volatile unsigned long *)(0x600060C4)) = 0xC0000000; /* 80 Mhz */ | ||
109 | IDE0_CFG &= ~0x10000000; | ||
110 | |||
111 | modeidx = mode & 7; | ||
112 | mode &= 0xF8; | ||
113 | if (mode == 0x40 && modeidx <= ATA_MAX_UDMA) { | ||
114 | IDE0_PRI_TIMING1 = tm_udma[modeidx]; | ||
115 | #if ATA_MAX_UDMA > 2 | ||
116 | if (modeidx > 2) | ||
117 | dma_needs_boost = true; | ||
118 | else | ||
119 | dma_needs_boost = false; | ||
120 | #endif | ||
121 | } else if (mode == 0x20 && modeidx <= ATA_MAX_MWDMA) | ||
122 | IDE0_PRI_TIMING1 = tm_mwdma[modeidx]; | ||
123 | |||
124 | IDE0_CFG |= 0x20000000; /* >= 50 Mhz */ | ||
125 | } | ||
126 | |||
127 | #define IDE_CFG_INTRQ 8 | ||
128 | #define IDE_DMA_CONTROL_READ 8 | ||
129 | |||
130 | /* This waits for an ATA interrupt using polling. | ||
131 | In ATA_CONTROL, CONTROL_nIEN must be cleared. | ||
132 | */ | ||
133 | STATICIRAM ICODE_ATTR int ata_wait_intrq(void) | ||
134 | { | ||
135 | long timeout = current_tick + HZ*10; | ||
136 | |||
137 | do | ||
138 | { | ||
139 | if (IDE0_CFG & IDE_CFG_INTRQ) | ||
140 | return 1; | ||
141 | ata_keep_active(); | ||
142 | yield(); | ||
143 | } while (TIME_BEFORE(current_tick, timeout)); | ||
144 | |||
145 | return 0; /* timeout */ | ||
146 | } | ||
147 | |||
148 | /* This function checks if parameters are appropriate for DMA, | ||
149 | and if they are, it sets up for DMA. | ||
150 | |||
151 | If return value is false, caller may use PIO for this transfer. | ||
152 | |||
153 | If return value is true, caller must issue a DMA ATA command | ||
154 | and then call ata_dma_finish(). | ||
155 | */ | ||
156 | bool ata_dma_setup(void *addr, unsigned long bytes, bool write) { | ||
157 | /* Require cacheline alignment for reads to prevent interference. */ | ||
158 | if (!write && ((unsigned long)addr & 15)) | ||
159 | return false; | ||
160 | |||
161 | /* Writes only need to be word-aligned, but by default DMA | ||
162 | * is not used for writing as it appears to be slower. | ||
163 | */ | ||
164 | #ifdef ATA_DMA_WRITES | ||
165 | if (write && ((unsigned long)addr & 3)) | ||
166 | return false; | ||
167 | #else | ||
168 | if (write) | ||
169 | return false; | ||
170 | #endif | ||
171 | |||
172 | #if ATA_MAX_UDMA > 2 | ||
173 | if (dma_needs_boost && !dma_boosted) { | ||
174 | cpu_boost(true); | ||
175 | dma_boosted = true; | ||
176 | } | ||
177 | #endif | ||
178 | |||
179 | if (write) { | ||
180 | /* If unflushed, old data may be written to disk */ | ||
181 | cpucache_flush(); | ||
182 | } | ||
183 | else { | ||
184 | /* Invalidate cache because new data may be present in RAM */ | ||
185 | cpucache_invalidate(); | ||
186 | } | ||
187 | |||
188 | /* Clear pending interrupts so ata_dma_finish() can wait for an | ||
189 | interrupt from this transfer | ||
190 | */ | ||
191 | IDE0_CFG |= IDE_CFG_INTRQ; | ||
192 | |||
193 | IDE_DMA_CONTROL |= 2; | ||
194 | IDE_DMA_LENGTH = bytes - 4; | ||
195 | |||
196 | #ifndef BOOTLOADER | ||
197 | if ((unsigned long)addr < DRAM_START) | ||
198 | /* Rockbox remaps DRAM to start at 0 */ | ||
199 | IDE_DMA_ADDR = (unsigned long)addr + DRAM_START; | ||
200 | else | ||
201 | #endif | ||
202 | IDE_DMA_ADDR = (unsigned long)addr; | ||
203 | |||
204 | if (write) | ||
205 | IDE_DMA_CONTROL &= ~IDE_DMA_CONTROL_READ; | ||
206 | else | ||
207 | IDE_DMA_CONTROL |= IDE_DMA_CONTROL_READ; | ||
208 | |||
209 | IDE0_CFG |= 0x8000; | ||
210 | |||
211 | return true; | ||
212 | } | ||
213 | |||
214 | /* This function waits for a DMA transfer to end. | ||
215 | It must be called to finish what ata_dma_setup started. | ||
216 | |||
217 | Return value is true if DMA completed before the timeout, and false | ||
218 | if a timeout happened. | ||
219 | */ | ||
220 | bool ata_dma_finish(void) { | ||
221 | bool res; | ||
222 | |||
223 | /* It may be okay to put this at the end of setup */ | ||
224 | IDE_DMA_CONTROL |= 1; | ||
225 | |||
226 | /* Wait for end of transfer. | ||
227 | Reading standard ATA status while DMA is in progress causes | ||
228 | failures and hangs. Because of that, another wait is used. | ||
229 | */ | ||
230 | res = ata_wait_intrq(); | ||
231 | |||
232 | IDE0_CFG &= ~0x8000; | ||
233 | IDE_DMA_CONTROL &= ~0x80000001; | ||
234 | |||
235 | #if ATA_MAX_UDMA > 2 | ||
236 | if (dma_boosted) { | ||
237 | cpu_boost(false); | ||
238 | dma_boosted = false; | ||
239 | } | ||
240 | #endif | ||
241 | |||
242 | return res; | ||
243 | } | ||
244 | |||
245 | #endif /* HAVE_ATA_DMA */ | ||