From efd047a08bf990b9d10be5e5df1bce83968bd4e4 Mon Sep 17 00:00:00 2001
From: Cástor Muñoz <cmvidal@gmail.com>
Date: Sat, 6 Dec 2014 23:13:44 +0100
Subject: iPod Classic: implement IPOD_ACCESSORY_PROTOCOL

Change-Id: I0f0950c42ae5bf5c5b4c2c2f097f8c68a92ba4dd
---
 .../target/arm/s5l8702/ipod6g/powermgmt-ipod6g.c   |   4 +-
 firmware/target/arm/s5l8702/ipod6g/serial-ipod6g.c | 108 +++++++++++++++++++++
 2 files changed, 110 insertions(+), 2 deletions(-)

(limited to 'firmware/target/arm')

diff --git a/firmware/target/arm/s5l8702/ipod6g/powermgmt-ipod6g.c b/firmware/target/arm/s5l8702/ipod6g/powermgmt-ipod6g.c
index ace66295f8..4553b03685 100644
--- a/firmware/target/arm/s5l8702/ipod6g/powermgmt-ipod6g.c
+++ b/firmware/target/arm/s5l8702/ipod6g/powermgmt-ipod6g.c
@@ -69,12 +69,12 @@ void accessory_supply_set(bool enable)
     if (enable)
     {
         /* Accessory voltage supply on */
-//TODO:        pmu_ldo_power_on(6);
+        pmu_ldo_power_on(6);
     }
     else
     {
         /* Accessory voltage supply off */
-//TODO:        pmu_ldo_power_off(6);
+        pmu_ldo_power_off(6);
     }
 }
 #endif
diff --git a/firmware/target/arm/s5l8702/ipod6g/serial-ipod6g.c b/firmware/target/arm/s5l8702/ipod6g/serial-ipod6g.c
index c03ba9bc24..b022fef675 100644
--- a/firmware/target/arm/s5l8702/ipod6g/serial-ipod6g.c
+++ b/firmware/target/arm/s5l8702/ipod6g/serial-ipod6g.c
@@ -41,6 +41,9 @@
 #define IPOD6G_UART_CLK_HZ      12000000    /* external OSC0 ??? */
 
 extern struct uartc s5l8702_uart;
+#ifdef IPOD_ACCESSORY_PROTOCOL
+void iap_rx_isr(int, char*, char*, uint32_t);
+#endif
 
 struct uartc_port ser_port IDATA_ATTR = {
     /* location */
@@ -54,7 +57,11 @@ struct uartc_port ser_port IDATA_ATTR = {
     .clkhz = IPOD6G_UART_CLK_HZ,
 
     /* interrupt callbacks */
+#ifdef IPOD_ACCESSORY_PROTOCOL
+    .rx_cb = iap_rx_isr,
+#else
     .rx_cb = NULL,
+#endif
     .tx_cb = NULL,  /* polling */
 };
 
@@ -85,3 +92,104 @@ void tx_writec(unsigned char c)
 {
     uartc_port_tx_byte(&ser_port, c);
 }
+
+#ifdef IPOD_ACCESSORY_PROTOCOL
+#include "iap.h"
+
+enum {
+    ABR_STATUS_LAUNCHED,    /* ST_SYNC */
+    ABR_STATUS_SYNCING,     /* ST_SOF */
+    ABR_STATUS_DONE
+};
+
+int abr_status;
+
+void serial_bitrate(int rate)
+{
+    logf("[%lu] serial_bitrate(%d)", USEC_TIMER, rate);
+
+    if (rate == 0) {
+        /* Using auto-bitrate (ABR) to detect accessory Tx speed:
+         *
+         * + Here:
+         *   - Disable Rx logic to clean the FIFO and the shift
+         *     register, thus no Rx data interrupts are generated.
+         *   - Launch ABR and wait for a low pulse in Rx line.
+         *
+         * + In ISR, when a low pulse is detected (ideally it is the
+         *   start bit of 0xff):
+         *   - Calculate and configure detected speed.
+         *   - Enable Rx to verify that the next received data frame
+         *     is 0x55 or 0xff:
+         *     - If so, it's assumed bit rate is correctly detected,
+         *       it will not be modified until speed is changed using
+         *       RB options menu.
+         *     - If not, reset iAP state machine and launch a new ABR.
+         */
+        uartc_port_set_rx_mode(&ser_port, UCON_MODE_DISABLED);
+        uartc_port_abr_start(&ser_port);
+        abr_status = ABR_STATUS_LAUNCHED;
+    }
+    else {
+        uartc_port_abr_stop(&ser_port); /* abort ABR if already launched */
+        uartc_port_set_bitrate(&ser_port, rate);
+        uartc_port_set_rx_mode(&ser_port, UCON_MODE_INTREQ);
+        abr_status = ABR_STATUS_DONE;
+    }
+}
+
+void iap_rx_isr(int len, char *data, char *err, uint32_t abr_cnt)
+{
+    /* ignore Rx errors, upper layer will discard bad packets */
+    (void) err;
+
+    static int sync_retry;
+
+    if (abr_status == ABR_STATUS_LAUNCHED) {
+        /* autobauding */
+        if (abr_cnt) {
+            #define BR2CNT(s) (IPOD6G_UART_CLK_HZ / (unsigned)(s))
+            unsigned speed;
+
+            if (abr_cnt < BR2CNT(57600*1.1) || abr_cnt > BR2CNT(9600*0.9)) {
+                /* detected speed out of range, relaunch ABR */
+                uartc_port_abr_start(&ser_port);
+                return;
+            }
+            /* valid speed detected, select it */
+            else if (abr_cnt < BR2CNT(48000)) speed = 57600;
+            else if (abr_cnt < BR2CNT(33600)) speed = 38400;
+            else if (abr_cnt < BR2CNT(24000)) speed = 28800;
+            else if (abr_cnt < BR2CNT(14400)) speed = 19200;
+            else speed = 9600;
+
+            /* set detected speed */
+            uartc_port_set_bitrate(&ser_port, speed);
+            uartc_port_set_rx_mode(&ser_port, UCON_MODE_INTREQ);
+
+            /* enter SOF state */
+            iap_getc(0xff);
+
+            abr_status = ABR_STATUS_SYNCING;
+            sync_retry = 2; /* we are expecting [0xff] 0x55 */
+        }
+    }
+
+    /* process received data */
+    while (len--) {
+        bool sync_done = !iap_getc(*data++);
+
+        if (abr_status == ABR_STATUS_SYNCING) {
+            if (sync_done) {
+                abr_status = ABR_STATUS_DONE;
+            }
+            else if (--sync_retry == 0) {
+                /* invalid speed detected, relaunch ABR
+                   discarding remaining data (if any) */
+                serial_bitrate(0);
+                break;
+            }
+        }
+    }
+}
+#endif /* IPOD_ACCESSORY_PROTOCOL */
-- 
cgit v1.2.3