From 1b779e0461f831631681bb16fecc4cfb7175de5a Mon Sep 17 00:00:00 2001 From: Michael Sevakis Date: Thu, 20 Jan 2011 06:41:05 +0000 Subject: PP502x USB: It seems r29087 introduced additional parasitic current consumption after USB disconnect. So, reinitialize the controller just like at startup when disabling USB, which also happens to fix FS#10719. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@29094 a1c6a512-1295-4272-9138-f99709370657 --- firmware/target/arm/usb-fw-pp502x.c | 45 ++++++++++++++++++------------------- 1 file changed, 22 insertions(+), 23 deletions(-) (limited to 'firmware/target/arm/usb-fw-pp502x.c') diff --git a/firmware/target/arm/usb-fw-pp502x.c b/firmware/target/arm/usb-fw-pp502x.c index e8711a6c26..19f21e12ed 100644 --- a/firmware/target/arm/usb-fw-pp502x.c +++ b/firmware/target/arm/usb-fw-pp502x.c @@ -106,19 +106,7 @@ #define USB_GPIO_INT_CLR GPIO_INT_CLR(USB_GPIO) #define USB_GPIO_HI_INT_MASK GPIO_HI_INT_MASK(USB_GPIO) -/* Enable raw status pin read only - not interrupt */ -void usb_pin_init(void) -{ - GPIO_CLEAR_BITWISE(USB_GPIO_OUTPUT_EN, USB_GPIO_MASK); - GPIO_SET_BITWISE(USB_GPIO_ENABLE, USB_GPIO_MASK); -#ifdef USB_FIREWIRE_HANDLING - /* GPIO C bit 1 is firewire detect */ - GPIO_CLEAR_BITWISE(GPIOC_OUTPUT_EN, 0x02); - GPIO_SET_BITWISE(GPIOC_ENABLE, 0x02); -#endif -} - -void usb_init_device(void) +static void usb_reset_controller(void) { /* enable usb module */ outl(inl(0x7000002C) | 0x3000000, 0x7000002C); @@ -139,9 +127,6 @@ void usb_init_device(void) udelay(100000); XMB_RAM_CFG |= 0x47A; - /* Do one-time inits */ - usb_drv_startup(); - /* disable USB-devices until USB is detected via GPIO */ #ifndef BOOTLOADER /* Disabling USB0 in the bootloader makes the OF not load, @@ -151,6 +136,26 @@ void usb_init_device(void) DEV_EN &= ~DEV_USB1; DEV_INIT2 &= ~INIT_USB; #endif +} + +/* Enable raw status pin read only - not interrupt */ +void usb_pin_init(void) +{ + GPIO_CLEAR_BITWISE(USB_GPIO_OUTPUT_EN, USB_GPIO_MASK); + GPIO_SET_BITWISE(USB_GPIO_ENABLE, USB_GPIO_MASK); +#ifdef USB_FIREWIRE_HANDLING + /* GPIO C bit 1 is firewire detect */ + GPIO_CLEAR_BITWISE(GPIOC_OUTPUT_EN, 0x02); + GPIO_SET_BITWISE(GPIOC_ENABLE, 0x02); +#endif +} + +void usb_init_device(void) +{ + usb_reset_controller(); + + /* Do one-time inits (no dependency on controller) */ + usb_drv_startup(); usb_pin_init(); @@ -186,14 +191,8 @@ void usb_enable(bool on) } else { usb_core_exit(); -#ifndef BOOTLOADER /* Disable USB devices */ - DEV_RS |= (DEV_USB0 | DEV_USB1); - DEV_RS &= ~(DEV_USB0 | DEV_USB1); - DEV_EN &=~ DEV_USB0; - DEV_EN &=~ DEV_USB1; - DEV_INIT2 &=~ INIT_USB; -#endif + usb_reset_controller(); } } -- cgit v1.2.3