From 08c41d42bb699a1be99c9696b4d4fb7b40e8723a Mon Sep 17 00:00:00 2001 From: Dave Chapman Date: Sun, 19 Oct 2008 14:11:01 +0000 Subject: Add e200v2 and m200v2 targets. Move the telechips lcd-ssd1815.c (currently used by Logik DAX and m200v1 ports) driver up in the target tree and share with the m200v2 - as2525 parts contributed by Rafael Carre. Includes the start (but is still very incomplete) of an LCD driver for the e200v2. m200v2 is not yet fully supported by mkamsboot - that will come soon. Also some minor cleanups for the Clip. git-svn-id: svn://svn.rockbox.org/rockbox/trunk@18836 a1c6a512-1295-4272-9138-f99709370657 --- firmware/target/arm/tcc77x/lcd-ssd1815.c | 256 ------------------------------- 1 file changed, 256 deletions(-) delete mode 100644 firmware/target/arm/tcc77x/lcd-ssd1815.c (limited to 'firmware/target/arm/tcc77x/lcd-ssd1815.c') diff --git a/firmware/target/arm/tcc77x/lcd-ssd1815.c b/firmware/target/arm/tcc77x/lcd-ssd1815.c deleted file mode 100644 index b41c8d26ef..0000000000 --- a/firmware/target/arm/tcc77x/lcd-ssd1815.c +++ /dev/null @@ -1,256 +0,0 @@ -/*************************************************************************** - * __________ __ ___. - * Open \______ \ ____ ____ | | _\_ |__ _______ ___ - * Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ / - * Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < < - * Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \ - * \/ \/ \/ \/ \/ - * $Id$ - * - * Copyright (C) 2002 by Alan Korr - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY - * KIND, either express or implied. - * - ****************************************************************************/ -#include "config.h" - -#include "hwcompat.h" -#include "kernel.h" -#include "lcd.h" -#include "system.h" -#include "cpu.h" - -/*** definitions ***/ - -#define LCD_SET_LOWER_COLUMN_ADDRESS ((char)0x00) -#define LCD_SET_HIGHER_COLUMN_ADDRESS ((char)0x10) -#define LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO ((char)0x20) -#define LCD_SET_POWER_CONTROL_REGISTER ((char)0x28) -#define LCD_SET_DISPLAY_START_LINE ((char)0x40) -#define LCD_SET_CONTRAST_CONTROL_REGISTER ((char)0x81) -#define LCD_SET_SEGMENT_REMAP ((char)0xA0) -#define LCD_SET_LCD_BIAS ((char)0xA2) -#define LCD_SET_ENTIRE_DISPLAY_OFF ((char)0xA4) -#define LCD_SET_ENTIRE_DISPLAY_ON ((char)0xA5) -#define LCD_SET_NORMAL_DISPLAY ((char)0xA6) -#define LCD_SET_REVERSE_DISPLAY ((char)0xA7) -#define LCD_SET_MULTIPLEX_RATIO ((char)0xA8) -#define LCD_SET_BIAS_TC_OSC ((char)0xA9) -#define LCD_SET_1OVER4_BIAS_RATIO ((char)0xAA) -#define LCD_SET_INDICATOR_OFF ((char)0xAC) -#define LCD_SET_INDICATOR_ON ((char)0xAD) -#define LCD_SET_DISPLAY_OFF ((char)0xAE) -#define LCD_SET_DISPLAY_ON ((char)0xAF) -#define LCD_SET_PAGE_ADDRESS ((char)0xB0) -#define LCD_SET_COM_OUTPUT_SCAN_DIRECTION ((char)0xC0) -#define LCD_SET_TOTAL_FRAME_PHASES ((char)0xD2) -#define LCD_SET_DISPLAY_OFFSET ((char)0xD3) -#define LCD_SET_READ_MODIFY_WRITE_MODE ((char)0xE0) -#define LCD_SOFTWARE_RESET ((char)0xE2) -#define LCD_NOP ((char)0xE3) -#define LCD_SET_END_OF_READ_MODIFY_WRITE_MODE ((char)0xEE) - -/* LCD command codes */ -#define LCD_CNTL_RESET 0xe2 /* Software reset */ -#define LCD_CNTL_POWER 0x2f /* Power control */ -#define LCD_CNTL_CONTRAST 0x81 /* Contrast */ -#define LCD_CNTL_OUTSCAN 0xc8 /* Output scan direction */ -#define LCD_CNTL_SEGREMAP 0xa1 /* Segment remap */ -#define LCD_CNTL_DISPON 0xaf /* Display on */ - -#define LCD_CNTL_PAGE 0xb0 /* Page address */ -#define LCD_CNTL_HIGHCOL 0x10 /* Upper column address */ -#define LCD_CNTL_LOWCOL 0x00 /* Lower column address */ - -/* TCC77x specific defines */ -#define LCD_BASE 0x50000000 -#define LCD_CMD *(volatile unsigned char*)(LCD_BASE) -#define LCD_DATA *(volatile unsigned char*)(LCD_BASE+1) - -void lcd_write_command(int byte) -{ - LCD_CMD = byte; - - asm volatile ( - "nop \n\t" - "nop \n\t" - "nop \n\t" - ); -} - -void lcd_write_data(const fb_data* p_bytes, int count) -{ - while (count--) - { - LCD_DATA = *(p_bytes++); - - asm volatile ( - "nop \n\t" - "nop \n\t" - "nop \n\t" - ); - } -} - -/* End of TCC77x specific defines */ - - -/** globals **/ - -static int xoffset; /* needed for flip */ - -/*** hardware configuration ***/ - -int lcd_default_contrast(void) -{ - return 0x1f; -} - -void lcd_set_contrast(int val) -{ - lcd_write_command(LCD_CNTL_CONTRAST); - lcd_write_command(val); -} - -void lcd_set_invert_display(bool yesno) -{ - if (yesno) - lcd_write_command(LCD_SET_REVERSE_DISPLAY); - else - lcd_write_command(LCD_SET_NORMAL_DISPLAY); -} - -/* turn the display upside down (call lcd_update() afterwards) */ -void lcd_set_flip(bool yesno) -{ - (void)yesno; - /* TODO */ -} - - -/* LCD init */ -void lcd_init_device(void) -{ - uint32_t bus_width; - - /* Telechips init the same as the original firmware */ - CSCFG1 &= 0xc3ffc000; - CSCFG1 |= 0x3400101a; - CSCFG1 |= (1 << 21); - CSCFG1 &= ~(1 << 21); - - bus_width = ((MCFG >> 11) & 0x3) ^ 3; - - CSCFG1 = (bus_width << 28) | - (3 << 26) | /* MTYPE = 3 */ - ((LCD_BASE >> 28) << 22) | /* CSBASE = 0x5 */ - (1 << 20) | /* Unknown */ - (3 << 11) | /* Setup time = 3 cycles */ - (3 << 3) | /* Pulse width = 3+1 cycles */ - (1 << 0); /* Hold time = 1 cycle */ - - /* SSD1815 inits like the original firmware */ - lcd_write_command(LCD_SET_DISPLAY_OFF); - lcd_set_flip(false); - lcd_write_command(LCD_SET_INTERNAL_REGULATOR_RESISTOR_RATIO | 5); - lcd_set_contrast(lcd_default_contrast()); - lcd_write_command(LCD_SET_POWER_CONTROL_REGISTER | 7); - /* power control register: op-amp=1, regulator=1, booster=1 */ - lcd_write_command(LCD_SET_BIAS_TC_OSC); - - /* 0xc2 = 110 000 10: Osc. Freq 110 - ??? - TC value 000 - "-0.01%/C (TC0, POR)" - Bias ratio 10 - "1/9, 1/7 (POR)" - */ - lcd_write_command(0xc2); - lcd_write_command(LCD_SET_DISPLAY_ON); - - lcd_clear_display(); - lcd_update(); -} - -/*** Update functions ***/ - -/* Performance function that works with an external buffer - note that by and bheight are in 8-pixel units! */ -void lcd_blit_mono(const unsigned char *data, int x, int by, int width, - int bheight, int stride) -{ - /* Copy display bitmap to hardware */ - while (bheight--) - { - lcd_write_command (LCD_CNTL_PAGE | (by++ & 0xf)); - lcd_write_command (LCD_CNTL_HIGHCOL | (((x+xoffset)>>4) & 0xf)); - lcd_write_command (LCD_CNTL_LOWCOL | ((x+xoffset) & 0xf)); - - lcd_write_data(data, width); - data += stride; - } -} - - -/* Performance function that works with an external buffer - note that by and bheight are in 8-pixel units! */ -void lcd_blit_grey_phase(unsigned char *values, unsigned char *phases, - int x, int by, int width, int bheight, int stride) -{ - (void)values; - (void)phases; - (void)x; - (void)by; - (void)width; - (void)bheight; - (void)stride; -} - -/* Update the display. - This must be called after all other LCD functions that change the display. */ -void lcd_update(void) ICODE_ATTR; -void lcd_update(void) -{ - int y; - - /* Copy display bitmap to hardware */ - for (y = 0; y < LCD_FBHEIGHT; y++) - { - lcd_write_command (LCD_CNTL_PAGE | (y & 0xf)); - lcd_write_command (LCD_CNTL_HIGHCOL | ((xoffset >> 4) & 0xf)); - lcd_write_command (LCD_CNTL_LOWCOL | (xoffset & 0xf)); - - lcd_write_data (lcd_framebuffer[y], LCD_WIDTH); - } -} - -/* Update a fraction of the display. */ -void lcd_update_rect(int, int, int, int) ICODE_ATTR; -void lcd_update_rect(int x, int y, int width, int height) -{ - int ymax; - - /* The Y coordinates have to work on even 8 pixel rows */ - ymax = (y + height-1) >> 3; - y >>= 3; - - if(x + width > LCD_WIDTH) - width = LCD_WIDTH - x; - if (width <= 0) - return; /* nothing left to do, 0 is harmful to lcd_write_data() */ - if(ymax >= LCD_FBHEIGHT) - ymax = LCD_FBHEIGHT-1; - - /* Copy specified rectange bitmap to hardware */ - for (; y <= ymax; y++) - { - lcd_write_command (LCD_CNTL_PAGE | (y & 0xf)); - lcd_write_command (LCD_CNTL_HIGHCOL | (((x+xoffset) >> 4) & 0xf)); - lcd_write_command (LCD_CNTL_LOWCOL | ((x+xoffset) & 0xf)); - - lcd_write_data (&lcd_framebuffer[y][x], width); - } -} -- cgit v1.2.3