1 files changed, 0 insertions, 86 deletions

diff --git a/firmware/target/mips/ingenic_x1000/spl-x1000.c b/firmware/target/mips/ingenic_x1000/spl-x1000.c
index ac3a17f69f..1abbdcd7a4 100644
--- a/firmware/target/mips/ingenic_x1000/spl-x1000.c
+++ b/firmware/target/mips/ingenic_x1000/spl-x1000.c
@@ -55,92 +55,6 @@ void* spl_alloc(size_t count)
     return heap;
 }
 
-/* Used by:
- * - FiiO M3K
- * - Shanling Q1
- *
- * Amend it and add #ifdefs for other targets if needed.
- */
-void spl_dualboot_init_clocktree(void)
-{
-    /* Make sure these are gated to match the OF behavior. */
-    jz_writef(CPM_CLKGR, PCM(1), MAC(1), LCD(1), MSC0(1), MSC1(1), OTG(1), CIM(1));
-
-    /* Set clock sources, and make sure every clock starts out stopped */
-    jz_writef(CPM_I2SCDR, CS_V(EXCLK));
-    jz_writef(CPM_PCMCDR, CS_V(EXCLK));
-
-    jz_writef(CPM_MACCDR, CLKSRC_V(MPLL), CE(1), STOP(1), CLKDIV(0xfe));
-    while(jz_readf(CPM_MACCDR, BUSY));
-
-    jz_writef(CPM_LPCDR, CLKSRC_V(MPLL), CE(1), STOP(1), CLKDIV(0xfe));
-    while(jz_readf(CPM_LPCDR, BUSY));
-
-    jz_writef(CPM_MSC0CDR, CLKSRC_V(MPLL), CE(1), STOP(1), CLKDIV(0xfe));
-    while(jz_readf(CPM_MSC0CDR, BUSY));
-
-    jz_writef(CPM_MSC1CDR, CE(1), STOP(1), CLKDIV(0xfe));
-    while(jz_readf(CPM_MSC1CDR, BUSY));
-
-    jz_writef(CPM_CIMCDR, CLKSRC_V(MPLL), CE(1), STOP(1), CLKDIV(0xfe));
-    while(jz_readf(CPM_CIMCDR, BUSY));
-
-    jz_writef(CPM_USBCDR, CLKSRC_V(EXCLK), CE(1), STOP(1));
-    while(jz_readf(CPM_USBCDR, BUSY));
-}
-
-void spl_dualboot_init_uart2(void)
-{
-    /* Ungate the clock and select UART2 device function */
-    jz_writef(CPM_CLKGR, UART2(0));
-    gpioz_configure(GPIO_C, 3 << 30, GPIOF_DEVICE(1));
-
-    /* Disable all interrupts */
-    jz_write(UART_UIER(2), 0);
-
-    /* FIFO configuration */
-    jz_overwritef(UART_UFCR(2),
-                  RDTR(3), /* FIFO trigger level = 60? */
-                  UME(0),  /* UART module disable */
-                  DME(1),  /* DMA mode enable? */
-                  TFRT(1), /* transmit FIFO reset */
-                  RFRT(1), /* receive FIFO reset */
-                  FME(1)); /* FIFO mode enable */
-
-    /* IR mode configuration */
-    jz_overwritef(UART_ISR(2),
-                  RDPL(1),      /* Zero is negative pulse for receive */
-                  TDPL(1),      /* ... and for transmit */
-                  XMODE(1),     /* Pulse width 1.6us */
-                  RCVEIR(0),    /* Disable IR for recieve */
-                  XMITIR(0));   /* ... and for transmit */
-
-    /* Line configuration */
-    jz_overwritef(UART_ULCR(2), DLAB(0),
-                  WLS_V(8BITS),         /* 8 bit words */
-                  SBLS_V(1_STOP_BIT),   /* 1 stop bit */
-                  PARE(0),              /* no parity */
-                  SBK(0));              /* don't set break */
-
-    /* Set the baud rate... not too sure how this works. (Docs unclear!) */
-    const unsigned divisor = 0x0004;
-    jz_writef(UART_ULCR(2), DLAB(1));
-    jz_write(UART_UDLHR(2), (divisor >> 8) & 0xff);
-    jz_write(UART_UDLLR(2), divisor & 0xff);
-    jz_write(UART_UMR(2), 16);
-    jz_write(UART_UACR(2), 0);
-    jz_writef(UART_ULCR(2), DLAB(0));
-
-    /* Enable UART */
-    jz_overwritef(UART_UFCR(2),
-                  RDTR(0),  /* FIFO trigger level = 1 */
-                  DME(0),   /* DMA mode disable */
-                  UME(1),   /* UART module enable */
-                  TFRT(1),  /* transmit FIFO reset */
-                  RFRT(1),  /* receive FIFO reset */
-                  FME(1));  /* FIFO mode enable */
-}
-
 static void init_ost(void)
 {
     /* NOTE: the prescaler needs to be the same as in system-x1000.c */